Book
Highest-rated tire shop in Fredericton on GoogleTires is all we doThe go-to for tires in FrederictonProudly Canadian, locally ownedWorkmanship guaranteed
TPMS · PitStop & Go

How to Reset a Tire Pressure Sensor

Most TPMS lights clear on their own once pressures are correct and the car has been driven. When one does not, there is a specific reason.

The light comes on, you put air in all four, and it stays on. Here is what is actually happening and how to clear it.

First, do the part that matters

Before resetting anything, set the pressures correctly. The right number is on the sticker inside the driver's door jamb, not the number moulded into the tire sidewall. The sidewall number is the maximum the tire can hold, not what your car wants.

Check them cold, meaning the car has sat for at least three hours or been driven less than about two kilometres. A tire that has been driven on reads several PSI higher and you will end up underinflated.

Then drive it

Most systems clear themselves. The sensors only transmit when the wheels are turning, and many cars need sustained driving above roughly 25 km/h for ten to twenty minutes before the module accepts the new readings and turns the light off.

If you set the pressures in the driveway and the light is on two minutes later, that is normal. Drive it and check again.

If it still will not clear

Work through these in order.

A pressure is still off. The spare counts on some vehicles. So does the tire you topped up in the cold that has since warmed up and now reads differently. Recheck all of them cold with a gauge you trust, not the gauge on the air hose at the pump.

The reset procedure was not run. Some vehicles have a manual reset: a button under the dash, a menu item in the instrument cluster, or a sequence in the infotainment settings. Your owner's manual has the exact steps for your car, and they vary enormously between makes.

A sensor battery is dead. TPMS sensors have a sealed battery that lasts roughly seven to ten years. It cannot be replaced on its own; the sensor is replaced as a unit. If your car is around that age and one wheel never reports, this is the most likely answer.

A sensor was damaged. Sensors sit on the valve stem inside the wheel. They get broken during careless tire changes, corroded by road salt, or snapped off by an air hose. New Brunswick winters are hard on them.

The sensors were never relearned. If you just had tires swapped onto different rims, or bought a second set of wheels, the car has to be taught which sensor IDs belong to which position. Without that relearn, the car is listening for sensors that are not there.

There is an important difference between a solid light and a blinking one.

Solid: at least one tire is low. Add air.

Blinking for about a minute at startup, then solid: the system itself has a fault. That is not a pressure message. It means a sensor is not communicating, and no amount of air will clear it.

If yours blinks, skip the air and get the system read.

What a relearn involves

A scan tool wakes each sensor, reads its ID, and writes those IDs into the vehicle's module in the correct corner order. Some vehicles relearn automatically after driving, some need the tool, and some need a specific sequence of ignition and pressure changes.

We stock TPMS sensors and do programming and relearns at our Fredericton shop, including on a second set of winter wheels. If you run two sets of rims, having sensors in both and relearning at each changeover is the thing that keeps this from being an annual argument with your dashboard.

A seasonal note

Expect the light in the first hard cold snap. Pressure drops roughly 1 PSI for every 5 degrees Celsius the temperature falls. A set that was perfect at 15 degrees in October is genuinely low at minus 10 in January, and the system is doing its job.

Top them up, drive it, and it goes out.

Frequently asked questions

Why is my TPMS light still on after filling the tires?

Most systems need the car driven above roughly 25 km/h for several minutes before the sensors transmit and the light clears. If it is still on after a decent drive, a pressure is likely still low or a sensor has failed.

Does a TPMS light mean a flat?

Not always. It triggers at roughly 25 percent below the placard pressure, which is low enough to damage a tire but not always low enough to look flat.

Can I just ignore it?

No. An underinflated tire builds heat, wears the outer edges, costs fuel and can fail at speed. The light exists because that is hard to see by eye.

Related

Book your visit at PitStop & Go

300 Wilsey Road #1, Fredericton, New Brunswick E3B 5J1 · (506) 248-6006