TPMS Sensor Replacement: When You Actually Need One
A TPMS light does not always mean a flat. Telling a pressure warning from a system fault saves you a lot of pointless air.
Most TPMS lights are a genuine low tire. Some are not, and the difference is easy to read once you know what to look for.
Solid light versus blinking light
This is the whole diagnostic and almost nobody knows it.
Solid light: at least one tire is below the threshold, which is usually around 25 percent under the placard pressure. Add air.
Blinking for roughly 60 to 90 seconds at every startup, then going solid: this is a system fault, not a pressure message. One or more sensors are not communicating with the vehicle. Adding air will not change anything.
If yours blinks, stop topping up tires and get the system read.
Why sensors fail
Battery, which is the most common. Direct TPMS sensors contain a sealed lithium battery that transmits for roughly seven to ten years. It cannot be replaced separately. When it dies, the sensor is replaced as a unit.
If your vehicle is around that age and one corner has stopped reporting, this is almost certainly it. The others are the same age and will follow.
Corrosion. Road salt is brutal on the valve stem and the aluminium of the sensor body. New Brunswick winters shorten sensor life compared to milder provinces. Corrosion at the stem base also causes slow air leaks, so a tire you keep topping up can be a failing sensor rather than a nail.
Physical damage. Sensors are broken during careless tire changes more often than anyone likes to admit. The sensor sits right at the bead, which is exactly where the mounting machine works. A technician who does not know a sensor is there, or does not position the wheel correctly, snaps it off.
Never relearned. If you just changed to a second set of wheels, the car may be looking for sensor IDs that are not on the vehicle. That is not a failed sensor, it is a missing relearn, and it needs a tool rather than parts.
The cold weather false alarm
In the first hard cold snap, lights come on all over Fredericton.
Pressure drops roughly 1 PSI for every 5 degrees Celsius. A set at 32 PSI on a mild October day is around 27 PSI at minus 10, which is close enough to the warning threshold to trigger it.
Nothing has failed. Top them up and the light goes out after a few minutes of driving.
Cold also finishes off marginal sensor batteries, so a sensor that was limping through the fall often dies in that same week. If you top up all four correctly and the light stays on, that is the likely explanation.
What a replacement involves
- The tire is dismounted from that wheel
- The old sensor is removed
- The new sensor is installed with a fresh service kit
- The tire is remounted and balanced
- The sensor ID is programmed and relearned to the vehicle in the correct corner position
Step five is the one that is easy to get wrong. The car has to know which ID is at which corner, or it will report the wrong tire.
The service kit people skip
Every direct sensor has a service kit: the valve core, the rubber grommet or seal, the retaining nut and the cap. These are consumable parts that corrode.
Renewing the kit at every tire changeover is what stops a slow leak developing around the stem base, and what stops the nut seizing so badly that the sensor is destroyed when it is next removed.
It is a small part of a changeover and it is the difference between a sensor reaching its full battery life and failing early.
Running two sets of wheels
If you have winters on their own rims and your car has direct TPMS, you need sensors in both sets and a relearn at each changeover.
The alternative, running the winter set with no sensors, means a warning light from November to April. We do not recommend it, because a light you have learned to ignore is the same light that will try to tell you about a real slow leak in February.
We stock TPMS sensors and do programming and relearns at our Fredericton shop, including on second sets. If your light is on and the pressures check out, bring it in and we will read what the system is actually reporting.
Frequently asked questions
How do I know if a TPMS sensor is dead rather than a tire being low?
A solid light means low pressure. A light that blinks for about a minute at startup then stays solid means a system fault, which usually means a sensor is not reporting.
Can a TPMS sensor battery be replaced?
No. The battery is sealed inside the sensor and the whole sensor is replaced as a unit.
Do I need to replace all four sensors at once?
Not necessarily, but if one has died of old age the other three are the same age. Many people replace all four to avoid repeat visits.
Related
Book your visit at PitStop & Go
300 Wilsey Road #1, Fredericton, New Brunswick E3B 5J1 · (506) 248-6006